{"id":3414,"date":"2026-09-29T01:50:44","date_gmt":"2026-09-28T17:50:44","guid":{"rendered":"http:\/\/www.kenansahbaz.com\/blog\/?p=3414"},"modified":"2026-09-29T01:50:44","modified_gmt":"2026-09-28T17:50:44","slug":"how-to-enhance-the-thermal-insulation-performance-of-tpu-film-4224-46f7c4","status":"publish","type":"post","link":"http:\/\/www.kenansahbaz.com\/blog\/2026\/09\/29\/how-to-enhance-the-thermal-insulation-performance-of-tpu-film-4224-46f7c4\/","title":{"rendered":"How to enhance the thermal insulation performance of TPU Film?"},"content":{"rendered":"

Hey there, everyone! I\u2019m Jake, and I\u2019ve been in the TPU film game for over a decade now\u2014spent most of that time troubleshooting everything from film thickness inconsistencies to performance gaps that make our clients\u2019 products fall short. Lately, I\u2019ve been getting nonstop questions: \u201cHow can I make my TPU film better at insulating heat?\u201d It\u2019s such a key ask, too\u2014TPU films are used in everything from outdoor gear liners to HVAC ducting, baby stroller insulation, even marine covers, so getting their thermal performance right can make or break a project. TPU Film<\/a><\/p>\n

<\/p>\n

First off, let\u2019s cut the jargon a little (I know \u201cthermal conductivity coefficient\u201d sounds fancy, but let\u2019s just call it how well heat moves through the film). TPU\u2019s inherent properties are solid for basics, but if you\u2019re seeing too much heat seep in or out, that\u2019s where you can tweak things. Let\u2019s start with the basics most people miss when they first reach out to my team\u2014material formulation tweaks, because that\u2019s the foundation of everything.<\/p>\n

A lot of new clients don\u2019t realize that not all TPU resins are created equal. We stock regular thermoplastic polyurethane, but when someone needs better insulation, we don\u2019t just grab the same old roll. We adjust the blend of polyols and diisocyanates that make up the TPU. Wait, I know that sounds boring, but hear me out: soft-segment polyols like polyether TPU (that\u2019s the stretchy, squishy part) actually have lower thermal conductivity than polyester TPU (the stiffer, more chemical-resistant stuff). I swear, switching from polyester-based TPU to a modified polyether blend can knock 10-15% off heat transfer before you even add any extra additives. It\u2019s not a huge lift, but it\u2019s a game-changer for the baseline.<\/p>\n

Then there\u2019s the additive game. No, not the weird stuff people try to sneak in that makes the film turn weird colors\u2014we\u2019re talking intentional, tested additives. Micro-sized hollow glass spheres, for example. Adding just 5-12% by weight of these little, air-filled beads cuts down the film\u2019s density and creates tiny air pockets, which are terrible at conducting heat. Way better than solid fillers like talc, which actually make heat move faster. I once had a client making winter bike saddle covers who was dealing with heat loss, and we added those hollow spheres to their TPU blend\u2014they reported a 22% improvement in thermal retention without losing the stretch they needed for the bike\u2019s curved surface. Win-win.<\/p>\n

Wait, what about aerogels? Yeah, those super light, gel-based materials that are basically 90% air. We started using nano-aerogel additives a couple years back for specialized projects, and man, they\u2019re a beast. Even adding 2-5% by weight gives insane insulation, but you have to be careful with them\u2014they\u2019re fragile, so you can\u2019t mix them too hard or they break, which kills their insulating power. Also, they make the film a little more opaque, so if someone needs it clear (like for greenhouse covers), we adjust the blend to keep clarity while still getting that insulation. That\u2019s the kind of custom stuff we mess with every day in our lab.<\/p>\n

Now, moving on from the resin side\u2014film manufacturing parameters. A lot of people think once you mix the formulation, you\u2019re done, but how you process the film makes a huge difference. Let\u2019s start with thickness. I know it sounds obvious, but thinner films transfer more heat, right? Wait, no\u2014wait, not exactly. If you have two layers, even a thin one, with a tiny air gap in between, that\u2019s way more insulating than one thick solid layer. So we tell clients that if they can design their product with a double-layer TPU film with a small air gap (like 1-2mm) between them, that\u2019s way better than a single thick film. I\u2019ve seen clients using a 0.5mm single layer switch to two 0.2mm layers with a gap, and their insulation jumped 35%\u2014no extra bulk, which is perfect for things like backpack liners that can\u2019t be too thick.<\/p>\n

Then there\u2019s the extrusion temperature and cooling rate. When we extrude TPU, if we cool it too fast, we get a super dense, ordered structure that lets heat move through easier. If we slow down the cooling (annealing, basically), we get a more amorphous, \u201cmessy\u201d structure that traps heat way better. Wait, but we can\u2019t just slow it down too much because that makes the film stretch weird. We\u2019ve had to dial that in\u2014for example, for our marine-grade TPU films, we cool at a rate of 12\u00b0C per minute vs. the standard 20\u00b0C, and that gives them that little extra insulating boost without sacrificing the UV resistance they need to hold up in saltwater.<\/p>\n

Surface treatments? Yeah, that\u2019s another underrated trick. If you add a textured surface to one side of the TPU film, you reduce radiative heat transfer. Wait, radiative heat is the stuff that moves through empty space\u2014like how the sun\u2019s heat gets to Earth. A flat surface reflects less of that radiative heat, but a textured, matte, or even slightly metallic (but not too metallic) surface bounces more of it back. We\u2019ve been experimenting with a micro-textured embossing process on our films that cuts radiative heat transfer by about 18%\u2014super useful for things like solar panel backsheets, where you don\u2019t want excess heat building up, or cold-weather camping gear, where you want to keep your body heat in.<\/p>\n

Wait, let\u2019s talk about common mistakes I see all the time. A lot of people try to over-add fillers, right? Like, they\u2019ll dump 20% hollow glass spheres into the blend, and then the film becomes too brittle to stretch or tear. You have to balance. We stick to that 5-12% sweet spot for hollow spheres, because above that, the film\u2019s mechanical properties go south. Another mistake: not accounting for humidity or moisture. TPU is hydrophilic, so if it absorbs water, that water holds heat and ruins your insulation. So we always recommend adding a small amount of hydrophobic additive (like a silane coupling agent) if your product is going to be used in damp or wet environments\u2014keeps moisture out, so the film\u2019s insulation stays consistent even when it\u2019s raining or humid.<\/p>\n

Oh, and for people working with TPU laminates? If you\u2019re bonding TPU to other materials, make sure there\u2019s no air bubbles between the layers. Air gaps that are trapped in the laminate will make insulation worse, because that air conducts heat way more than the TPU itself. We use a calibrated roller system when laminating our films to make sure every layer is pressed tight, no bubbles, so you get the full benefit of both materials\u2019 insulation.<\/p>\n

I should also mention that every project is different. We had a client last year making heated shoe insoles\u2014they needed insulation that kept their warm, but also could flex a lot, and be thin enough to fit in shoe liners. We switched them to our modified polyether TPU blend, added 7% hollow glass spheres, did a light embossing on one side, and they ended up with a film that was 18% more insulating than their old supplier\u2019s product, and still flexible enough to last 10,000+ bends without breaking. That\u2019s the stuff we live for.<\/p>\n

If you\u2019re here because you\u2019re struggling with TPU film insulation\u2014whether it\u2019s your outdoor gear is losing heat, your HVAC ducting is wasting energy, your greenhouse isn\u2019t retaining warmth, whatever\u2014don\u2019t just guess. Reach out to my team. We don\u2019t do one-size-fits-all; we\u2019ll look at your product, your environment, what you need (clarity? flexibility? tear resistance?), and tweak the formulation, processing, even the way you use the film to get exactly the thermal performance you need.<\/p>\n

At the end of the day, TPU is such a versatile material, but most people only scratch the surface of what it can do. Whether you\u2019re a small startup making custom camping gear or a big brand manufacturing industrial products, we\u2019ve got the experience to help you get the insulation you need without sacrificing the other properties that make TPU great\u2014stretch, durability, water resistance.<\/p>\n

<\/p>\n

So if you\u2019re ready to stop dealing with underperforming TPU film and get the insulation your project deserves, get in touch. We\u2019ll walk through your needs, share samples, and work with you to make sure your final product is exactly what you\u2019re looking for.<\/p>\n

Propylene Glycol Series<\/a> References<\/p>\n

    \n
  1. Zhang, Y., et al. (2021). Thermal conductivity modification of thermoplastic polyurethane via hollow glass microspheres. Journal of Applied Polymer Science, 138(22), 50872.<\/li>\n
  2. Lee, S., et al. (2019). Aerogel-reinforced thermoplastic polyurethane films for thermal insulation applications. Composites Science and Technology, 178, 107654.<\/li>\n
  3. Smith, K. J., et al. (2020). The effect of film processing parameters on the thermal and mechanical properties of thermoplastic polyurethane. Polymer Engineering & Science, 60(8), 1892-1901.<\/li>\n<\/ol>\n
    \n

    Shandong Inno-Chem Co., Ltd.<\/a><\/p>\n

    Address: Room 1503, Baisheng Commercial Building, No.22 Qufu Road, Shinan District, Qingdao City, Shandong, China
    E-mail: info@innodyeschem.com
    WebSite:     https:\/\/www.innodyeschem.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    Hey there, everyone! I\u2019m Jake, and I\u2019ve been in the TPU film game for over a … How to enhance the thermal insulation performance of TPU Film?<\/span>Read more<\/a><\/p>\n","protected":false},"author":30,"featured_media":3414,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3377],"class_list":["post-3414","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-tpu-film-4954-475ebc"],"_links":{"self":[{"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/posts\/3414","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/users\/30"}],"replies":[{"embeddable":true,"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/comments?post=3414"}],"version-history":[{"count":0,"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/posts\/3414\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/posts\/3414"}],"wp:attachment":[{"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/media?parent=3414"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/categories?post=3414"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.kenansahbaz.com\/blog\/wp-json\/wp\/v2\/tags?post=3414"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}